nevrStic™ will readily free rusted and salt corroded boat fittings and parts, light sockets, switches, hinges, locks, steering cables, shackle bolts, slides, etc

Use on all external fittings, aerials, lights, switches, hinges, locks, radar and radio brackets, air conditioning unit and fan motors, refrigeration units, etc on an ongoing basis will keep these items in a good serviceable corrosion free condition for their full intended life.

Use internally to protect wiring harnesses and cables, radar, radios, GPS and sounder equipment, all switches and light fittings. Spray into starter motors, alternators, generators, relays, regulators, solenoids to protect from moisture and corrosion.

Use nevrStic™ on oar locks, anchor shackles and chains for protection from corrosion.

Spray over battery cradles and brackets to prevent corrosion. Use grease on battery terminals to protect them from corrosion.

Add Battery Conditioner to all lead-acid batteries for longer life, better performance and quicker recharging. It also reduces the self - discharge rate of the battery by 50% when not being used in the lay season.

Use externally to lubricate cables, locks and hinges, linkages, sliding hatches, winches, starter motors, generators, alternators, sliding windows and doors, sail tracks (ideal), deck pulleys and any other equipment or fittings that requires a good anti-corrosion lubricant.

Use grease to lubricate steering cables, engine and gearbox control cables, deck winch bearings, cable guides and winch cables. is virtually waterproof and a anti-corrosion lubricant.

After washing down with fresh water, spray all over jet ski motors and outboards, power legs, cables and linkages for ongoing protection against moisture and corrosion. May affect some rubbers with long term use.

nevrStic™ anti-corrosion, anti-moisture lubricants are ideal for marine use, they do not dry out or wash off with water, they are non-conductive and non-staining and stop electrolysis between aluminium and stainless steel in salt water.

Use nevrStic™ lubricant to protect jet ski motors and fittings. may affect some jet ski rubber seals with long term use.

Use nevrStic™ to protect light fittings, wiring and plugs from corrosion on towbars and grease on tow-balls.

Use nevrStic™ for the protection from corrosion for light fittings, wiring and plugs, Melt grease and paint it on the chassis, axles and springs and use Extreme Pressure P.T.F.E. grease for the trailer wheel bearings.

Spray on oxidized fibreglass hulls and buff polish off with a rotary polisher. Cleans off the oxidization and protects against further oxidization, leaves the hull looking like new.

Melt grease and paint on all metal fittings below the water line for anti-fouling and corrosion protection, on metal hulls, propellors, rudders, water in/outlets, bow thrusters, etc. Stops marine growth for to 2 years. Stops electrolysis between dissimilar metals.The Great Lakes, USA, grease painted on hulls below the waterline will stop the growth of Zebra clams on the hull.

For corrosion protection, melt grease and paint it on all above deck metal booms and hinge pins, motor, drum and winch housings, winch and drum cables, pulley blocks, radio antennas and radar equipment, all metal deck fittings, shackles, anchors and chains.

nevrStic™ is a very good lubricant for cutting, drilling, tapping and machining aluminium and stainless steel. With aluminium it stops tool chatter and tool creep, tearing and burring, leaves a very fine, clean cut finish. nevrStic™ is also a good tapping and thread cutting lubricant for copper rod, brass and Monel nuts used on the larger old style timber sailing boats and fishing trawlers. Use on carborundum stones for sharpening knives, hooks, chisels, etc.

Use nevrStic™ for protection from corrosion and damaging salt moisture spray on outboard motors and power legs, into all light fittings and switches on boats and trailers, electronic circuits, wiring harness, radios, radar and antennas, starter motors, generators and alternators, gauges, air conditioning and refrigeration fan motors and anywhere corrosion is a problem.